DYQCF-7 engine assembly and electrical wiring experimental device

Release time：2024-06-03 05:31viewed：times

1. Product Introduction
This equipment is composed of a simple engine assembly stand and an operating accessory stand. The bench provides students with hands-on tr*ning on engine assembly disassembly and assembly, and engine electrical
circuit connection. After the engine assembly and the engine electrical circuit are manually assembled and assembled, the engine can be started and run to test the engine's operating conditions.
two. Functional features
1. Install a full set of real operable engines and operating accessories;
2. Easily implement engine assembly scenario tr*ning.
3. The bench can connect oil circuits, electric circuits, water circuits, and gas circuits, run the engine (acceleration/deceleration/idling conditions are normal), and detect the operating conditions of disassembly and assembly of the engine assembly.
4. The bench can be used for engine assembly and manual overlapping of engine electrical circuits;
5. The tr*ning bench is equipped with a diagnostic socket, which can be connected to a special or general automotive decoder to read and clear fault codes for the engine electronic control system. , read data stream and other self-diagnostic functions. (Model optional)
6. The tr*ning platform is equipped with a m*n power switch, flywheel protective cover and other installation protection devices.
7. The tr*ning platform can easily realize overlapping tr*ning on engine m*ntenance, m*ntenance, and electrical circuit control principles.
8. The base of the tr*ning platform is welded with a steel structure, and the surface is spray-coated. It is equipped with self-locking casters, making it flexible to move, safe, reliable, sturdy and durable.
9. Mechanical assembly and fitter assembly virtual simulation software: This software is developed based on unity3d, with optional 6-level image quality. It is equipped with the design and virtual disassembly and assembly of reducers and shafting structures, the design and simulation of common mechanical mechanisms , and a mechanism resource library. For a typical mechanical mechanism (virtual disassembly and assembly of a gasoline engine), the software is a whole software and cannot be individual resources.
A. Reducer design and virtual disassembly interface can choose worm gear bevel gear reducer, two-stage expanded cylindrical gear reducer, bevel cylindrical gear reducer, coaxial cylindrical gear reducer, bevel gear reducer, and one-stage cylindrical gear reducer. Gear reducer.
Worm bevel gear reducer: After entering the software, the assembly content is automatically played. Each step in the video has a text description
. Secondary expandable cylindrical gear reducer: After entering the software, the content is played in the form of a video. The video content should include: Part name ( Scan the QR code to see the names of parts), disassembly and assembly demonstration (including disassembly and assembly), virtual disassembly (including overall, low-speed shaft, medium-speed shaft, high-speed shaft, box cover, box seat)
conical cylindrical gear reducer, Coaxial cylindrical gear reducer, bevel gear reducer, first-level cylindrical gear reducer: click to enter and automatically jump to the edrawings interface. The models are all three-dimensional models. By clicking on the parts, the names of the parts are displayed, and the 360° view is av*lable Rotate, zoom in, zoom out, pan, and move parts to disassemble and assemble the entire reducer. At the same time, you can select the home button to return to the original state of the reducer. The bevel gear reducer and the first-stage cylindrical gear reducer have added the function of inserting a cross section, and the cross section can be freely dragged to observe the internal structure of the reducer.
B. Shaft structure design and virtual disassembly and assembly interface optional parts recognition, disassembly and assembly demonstration, and actual operation.
1. Parts recognition: three-dimensional model and part name including helical gear, non-hole end cover, coupling, coupling key, shaft, gear key, hole end cover, shaft sleeve, deep groove ball bearing, any All parts can be rotated 360°
2. Disassembly and assembly demonstration: There are 2 built-in cases. When you move the mouse to the position of a cert*n part (except the base and bearing seat), the part will automatically enlarge and the name of the part will be displayed. It is equipped with disassembly and Assembly button, the function is to automatically complete the disassembly and assembly of the shaft system structure by the software. All three-dimensional scenes can be rotated, enlarged, reduced and translated 360° in all directions.
3. Practical operation: The three-dimensional parts are neatly placed on the table. Students manually select the corresponding parts and move them to the shaft system structure. The parts can be installed only when they are placed in the correct order and in the correct position. There is a restart button to facilitate students to restart. Conduct virtual experiments. When you move the mouse to a cert*n part position (except the base and bearing seat), the part will automatically enlarge and the part name will be displayed.
C. Common mechanical mechanism design and simulation, optional hinge four-bar mechanism design and analysis, I\II type crank rocker mechanism design and analysis, offset crank slider mechanism design and analysis, crank swing guide rod mechanism design and analysis, hinge Four-bar mechanism with integrated trajectory, eccentric linear-acting roller push rod cam , and centering linear-acting flat-bottomed push rod cam.
1. Each mechanism should be able to input corresponding parameters, and the software can automatically calculate the parameters, and can perform motion simulation and automatically draw curves.
D. The mechanism resource library includes 11 types of planar link mechanisms, 5 types of cam mechanisms, 6 types of gear mechanisms, 8 types of transmission mechanisms, 11 types of tightening mechanisms, 6 types of gear tr*n mechanisms, and 8 types of other mechanisms (mechanical equipment simulation)
E , virtual disassembly and assembly of gasoline engines, optional crankcase assembly and disassembly demonstration, crankcase virtual assembly, valve tr*n assembly and disassembly demonstration, valve tr*n virtual assembly
1. Crankcase assembly and disassembly demonstration and valve tr*n assembly and disassembly demonstration both have disassembly button, assembly button, restart, and decomposition observation button. When the mouse is moved to a cert*n part position, the part will automatically enlarge and the part name will be displayed. The software automatically completes the disassembly and assembly of the shaft system structure. When using the decomposition observation button, the 3D model of the crankcase or gas distribution system automatically displays an exploded view, which can be rotated, enlarged, reduced, and translated 360°.
2. The 3D parts of the crankcase virtual assembly and the gas distribution system virtual assembly are neatly arranged When placed on the desktop, students manually select the corresponding parts and move them to the mechanism. The parts can be installed only when they are placed in the correct order and in the correct position. There is a restart button to facilitate students to re-perform the virtual experiment. When you move the mouse to cert*n part locations, the part names are automatically displayed.
three. Technical specifications
Working power source: Original vehicle
Fuel label: According to engine model
Fuel tank volume: 10L
Working temperature: -40℃～+50℃
Color: 7032
Steel pipe: 40*40*3mm
Mobile casters: 120*80mm
Mobile stand (with self-locking caster device): 1000*700*1200mm (length*width*height)
4. Basic configuration (per set)

serial number	name	Specifications and models	unit	quantity
1	Engine control computer (ECU)	Original car	set	1
2	instrument cluster	Original car	set	1
3	Diagnostic seat	Original car	indivual	1
4	Ignition Switch	Original car	indivual	1
5	Fuel tank	10L	indivual	1
6	Fuel pump (including fuel pump plug)	brand new	set	1
7	Water tank and accessories	Original car	set	1
8	cooling electronic fan	12V, 80W	indivual	2
9	battery	12V 65Ah	tower	1
10	relay	Including: starting relay, oil pump relay, cooling fan relay, etc.	set	1
11	Wiring harness		set	1
12	Fuse box	Relay box (with fuse holder) integral type	indivual	1
13	m*n power switch	50A	indivual	1
14	Mobile stand (with self-locking casters)	10007001200mm (lengthwidthheight)	tower	1
15	Engine assembly	Original car	set	1
16	Intake and exhaust pipes	Original car	set	1
17	three way catalytic converter	With new muffler	set	1
18	Final assembly equipment (optional)		set	1

Previous：DYQCF-8 engine+transmission integrated maintenance experimental device

Next：DYQCF-6 gasoline engine disassembly and operation experimental device