DYXNYQD-11 thermal management system intelligent experimental device
Release time：2024-05-26 04:00viewed：times
1. Product Introduction
This equipment is based on the electric vehicle drive motor cooling system and comprehensively demonstrates the composition and working process of the electric vehicle drive motor cooling system. It is suitable for the teaching needs of schools on the theory and m*ntenance tr*ning of electric vehicle drive motor cooling systems.
2. Functional features
1. Run the demonstration electric vehicle drive motor cooling system to fully demonstrate the composition and structure of the electric vehicle drive motor cooling system.
2. Operate the control switch to demonstrate the working process of the electric vehicle drive motor cooling system, and install flashing light-emitting diodes to synchronously demonstrate the working process of the system.
3. The panel is made of 4mm thick aluminum-plastic plate, and the panel is UV flatbed printed with a color diagram; students can visually compare the diagram and the actual object to understand and analyze the working principle of the system.
4. There are detection terminals installed on the panel, which can directly detect the electrical signals of system circuit components on the panel, such as resistance, voltage, current, frequency signals, etc.
5. The water-cooled drive motor is dissected and sprayed with different colors on each section, so that the mechanical structure of the internal and external components and the assembly relationship between each other are clearly displayed on the outside.
6. The equipment frame is constructed of two integrated all-aluminum alloy profiles, 40mm×40mm and 40mm×80mm, which are oil-resistant, corrosion-resistant and easy to clean. The countertop is 40CM wide and paved with 32mm thick colored high-density composite boards, which is durable and rust-free. , with 4 swivel casters with self-locking devices for easy movement.
7. Supporting teaching materials such as tr*ning guides, including working principles, practical tr*ning projects, fault analysis and other key points.
8. Mechanical assembly and fitter assembly virtual simulation software: This software is developed based on unity3d, with optional 6-level image quality. It is equipped with the design and virtual disassembly and assembly of reducers and shafting structures, the design and simulation of common mechanical mechanisms , and a mechanism resource library. For a typical mechanical mechanism (virtual disassembly and assembly of a gasoline engine), the software is a whole software and cannot be individual resources.
A. Reducer design and virtual disassembly interface can choose worm gear bevel gear reducer, two-stage expanded cylindrical gear reducer, bevel cylindrical gear reducer, coaxial cylindrical gear reducer, bevel gear reducer, and one-stage cylindrical gear reducer. Gear reducer.
Worm bevel gear reducer: After entering the software, the assembly content is automatically played. Each step in the video has a text description
. Secondary expandable cylindrical gear reducer: After entering the software, the content is played in the form of a video. The video content should include: Part name ( Scan the QR code to see the names of parts), disassembly and assembly demonstration (including disassembly and assembly), virtual disassembly (including overall, low-speed shaft, medium-speed shaft, high-speed shaft, box cover, box seat)
conical cylindrical gear reducer, Coaxial cylindrical gear reducer, bevel gear reducer, first-level cylindrical gear reducer: click to enter and automatically jump to the edrawings interface. The models are all three-dimensional models . By clicking on the parts, the names of the parts are displayed, and the 360° view is av*lable Rotate, enlarge, reduce, translate, and at the same time, the entire reducer can be disassembled and assembled through the moving parts function. At the same time, you can select the home button to return to the original state of the reducer. The bevel gear reducer and first-stage cylindrical gear reducer have added the function of inserting a cross section, and the cross section can be freely dragged to observe the internal structure of the reducer.
B. Shaft structure design and virtual disassembly and assembly interface optional parts recognition, disassembly and assembly demonstration, and actual operation.
1. Parts recognition: three-dimensional model and part name including helical gear, non-hole end cover, coupling, coupling key, shaft, gear key, hole end cover, shaft sleeve, deep groove ball bearing, any All parts can be rotated 360°
2. Disassembly and assembly demonstration: There are 2 built-in cases. When you move the mouse to the position of a cert*n part (except the base and bearing seat), the part will automatically enlarge and the name of the part will be displayed. It is equipped with disassembly and Assembly button, the function is to automatically complete the disassembly and assembly of the shaft system structure by the software. All three-dimensional scenes can be rotated, enlarged, reduced and translated 360° in all directions.
3. Practical operation: The three-dimensional parts are neatly placed on the table. Students manually select the corresponding parts and move them to the shaft system structure. The parts can be installed only when they are placed in the correct order and in the correct position. There is a restart button to facilitate students to restart. Conduct virtual experiments. When you move the mouse to a cert*n part position (except the base and bearing seat), the part will automatically enlarge and the part name will be displayed.
C. Common mechanical mechanism design and simulation, optional hinge four-bar mechanism design and analysis, I\II type crank rocker mechanism design and analysis, offset crank slider mechanism design and analysis, crank swing guide rod mechanism design and analysis, hinge Four-bar mechanism with integrated trajectory, eccentric linear-acting roller push rod cam , and centering linear-acting flat-bottomed push rod cam .
1. Each mechanism should be able to input corresponding parameters, and the software can automatically calculate the parameters, and can perform motion simulation and automatically draw curves.
D. The mechanism resource library includes 11 types of planar link mechanisms, 5 types of cam mechanisms, 6 types of gear mechanisms, 8 types of transmission mechanisms, 11 types of tightening mechanisms, 6 types of gear tr*n mechanisms, and 8 types of other mechanisms (mechanical equipment simulation)
E , virtual disassembly and assembly of gasoline engines, optional crankcase assembly and disassembly demonstration, crankcase virtual assembly, valve tr*n assembly and disassembly demonstration, valve tr*n virtual assembly
1, crankcase assembly and disassembly demonstration and valve tr*n assembly and disassembly demonstration both have disassembly button, assembly button, restart, and decomposition observation button. When the mouse is moved to a cert*n part position, the part will automatically enlarge and the part name will be displayed. The software automatically completes the disassembly and assembly of the shaft system structure. When the decomposition observation button is used, the 3D model of the crankcase or gas distribution system automatically displays an exploded view, which can be rotated, enlarged, reduced, and translated 360°.
2. The 3D parts of the crankcase virtual assembly and the gas distribution system virtual assembly are neatly arranged When placed on the desktop, students manually select the corresponding parts and move them to the mechanism. The parts can be installed only when they are placed in the correct order and in the correct position. There is a restart button to facilitate students to re-perform the virtual experiment. When you move the mouse to cert*n part locations, the part names are automatically displayed.
3. Technical specifications
1. Input power supply; AC 220V±10% 50Hz
2. Working power supply; DC12V
3. Working temperature: -40℃～+50℃
4. Equipment dimensions (mm): 1500×700×1700mm (length*width*height)
5. Panel dimensions (mm): 1448×940mm (length*width)
6. Water-cooled motor: BAIC EV160
4. Practical tr*ning experiment Project
1. Understanding the structure and principles of the drive motor cooling system.
2. Recognition and detection of the terminals and corresponding functions of the drive motor cooling system.
5. Basic configuration:
detection control panel (equipped with various detection terminals and color circuit diagrams), electronic water pump, cooler and kettle, water pipe, ignition switch, water temperature sensor /temperature signal simulation device, simulated water cooling system control device, electronic fan A mobile bench built with relays, water-cooled motors (BAIC EV160, dissected), DC12V devices, and integrated all-aluminum alloy profiles (1500×700×1700mm with self-locking caster device, principle panel with installation detection terminals, panel 1448×940mm ), equipment operating instructions.
Wechat scan code follow us
