Engine electronic fuel injection training device

Engine electronic fuel injection tr--ning device,New Energy AC-DC conversion device demonstration and tr--ning desk

1. Product introduction

The device is made of physical electronic fuel injection system, which fully displays the structure and working process of the electronic fuel injection system.

It is suitable for the teaching needs of the school's theory and m--ntenance tr--ning for engine fuel injection systems.

2. Functional characteristics

1. Real and running engine fuel injection system, fully display the composition and working process of the fuel injection system. Rotating the crankshaft position signal wheel, you can demonstrate the process of e -fuel injection.

2. The teaching plate panel adopts high -grade aluminum -plastic panels with strikes, pollution resistance, fire resistance, and moisture -proof, and sprayed on the surface by special crafts; panel prints with color circuit diagrams that never fade and work. Circuit diagrams and physical objects, understand and analyze the working principle of electronic fuel injection systems.

3. The detection terminal is installed on the teaching panel, which can directly detect the electronic fuel injection system circuit components on the panel, such as resistance, voltage, current, frequency signal, etc.

4. Diagnostic seat installation of the teaching board can be connected to a dedicated or general -purpose car decoder to read the fault code, remove the fault code, and the data flow of the engine electrical control system.

5. Demonstration panel parts use a 1.5mm cold plate stamping formation structure, beautiful appearance; the ch--n part is welded with steel structure, the surface is treated with a spraying process, a self -locking wheel device, and the base of the teaching plate is equipped with about 40cm. Desktop, convenient to place data, detect instruments, etc.

6. The work of the teaching board adopts a normal 220V AC power supply. The internal circuit transformer is transformed into a 12V DC power supply. No battery is required to reduce the trouble of charging. The 12V DC power supply has a short circuit function.

7. Machinery assembly and fitter assembly virtual simulation software: This software is developed based on Unity3D. It can select 6 -level image quality. It has the design and virtual disassembly of the reducer and shaft structure, the design and simulation of common mechanical institutions, institutional resource libraries, institutional resource libraries. Typical mechanical institutions (virtual disassembly of gasoline engines), software is an overall software, which cannot be separate resources.

A. Turbine design and virtual disassembly interface can be selected from turbine sn--l pole cone gear reducer, second -level pilot gear reducer, conical cylindrical gear reducer, coaxial cylindrical gear reducer, cone gear reducer, first -class cylindrical, first -class cylindrical, Gear reducer.

Engine electronic fuel injection tr--ning device,New Energy AC-DC conversion device demonstration and tr--ning desk

1. Functional characteristics

1. The device fully demonstrates the new energy vehicle power transformation system, which can overlap DC-AC, AC-DC, voltage voltage, lower voltage and other circuits to display the structure and control logic of each system.

2. The panel adopts high -grade aluminum -plastic panels with 4mm thick corrosion, strike resistance, pollution resistance, fire prevention, and moisture -proof, and the surface is sprayed with primer p--nt by special crafts; the panel prints with color circuit diagrams and work diagram of the principle of never fading; students can be students. Awarely compare the working principles of the new energy vehicle power transformation structure and physical objects to understand and analyze the working principle of the power transformation system of the new energy vehicle.

3. Install a little fire switch on the panel, DC-AC, AC-DC, voltage voltage, antihypertensive module, etc., supplemented by the dynamic instructions of the system flowing with the light-emitting diode, and there is also an simulation indicator light to demonstrate the power conversion of power supply conversion State, the position of the key component is set to detect the terminal, and the special instrument can be used to measure the parameters.

4. The panel adopts a high -grade aluminum -plastic plate with 4mm thick corrosion, strike resistance, pollution resistance, fire prevention, and moisture -proof. The surface is sprayed with primer p--nt by special process; the panel prints a color circuit diagram that will never fade.

5. Machinery assembly and fitter assembly virtual simulation software: This software is developed based on Unity3D, which can choose 6 -level image quality. It has the design and virtual disassembly of the reducer and shaft structure, the design and simulation of common mechanical institutions, institutional resource libraries, institutional resource libraries. Typical mechanical institutions (virtual disassembly of gasoline engines), software is an overall software, which cannot be separate resources.

A. Turbine design and virtual disassembly interface can be selected from turbine sn--l pole cone gear reducer, second -level pilot gear reducer, conical cylindrical gear reducer, coaxial cylindrical gear reducer, cone gear reducer, first -class cylindrical, first -class cylindrical, Gear reducer.

The turbine sn--l tapered gear reducer: automatically play the assembly content after entering the software. Each step in the video has text description

Second -level unfolding cylindrical gear reducer: After entering the software, use the video to play content in the form of video. The video content should include: the name of the parts (scanning the QR code can see the part of the parts), the disassembly presentation (including disassembly, assembly), virtual disassembly Installation (including overall, low -speed shaft, mid -speed axis, high -speed shaft, box cover, box seat)

Cone cylindrical gear reducer, coaxial cylindrical gear reducer, conical gear reducer, first -class cylindrical gear reducer: After clicking, automatically jump to the Edrawings interface. The models are all three -dimensional models. It can rotate, magnify, shrink, and translate in 360 ° in all directions. At the same time, the entire reducer can be disassembled and assembled through the function of mobile parts. At the same time, you can select the homepage button to return to the initial state of the reducer. The cone gear reducer and first -class cylindrical gear reducer increase the plug -in horizontal surface function, which can freely drag the horizontal surface to observe the internal structure of the reducer.

B. Design and virtual disassembly interface of the shaft system can optional part recognition, disassembly presentation, and actual combat operation.