DY-268 Anaerobic Reactor Training Platform

Release time：2024-06-25 02:30viewed：times

1. Purpose of anaerobic experiment:
Anaerobic biological treatment technology is not only used for organic sludge and high-concentration organic wastewater, but also can treat low-concentration sewage. Compared with aerobic biological treatment technology, anaerobic biological treatment has a series of obvious advantages such as high organic load, low sludge production and low energy consumption. A major structure of anaerobic biological treatment, it integrates anaerobic biological reaction and sedimentation separation, has high organic load and removal efficiency, and does not require stirring equipment. This model is a teaching experimental equipment for anaerobic reactors. Through this experiment, we hope to achieve the following goals:
1. Understand the internal structure of anaerobic;
2. Master the start-up method of anaerobic and the formation mechanism of granular sludge;
3. Conduct dynamic tests on a cert*n sewage to determine the process parameters and the water quality of the treated water.
2. Purpose of membrane reaction experiment:
The membrane bioreactor sewage treatment device is a test device for an integrated membrane bioreactor. The membrane bioreactor is a new sewage treatment process produced by the organic combination of membrane technology and sewage biological treatment technology. Its production and development are the inevitable result of the application and development of these two types of knowledge. The cross-disciplinary and combined membrane technology and sewage biological treatment technology have opened up a new field for sewage treatment technology research and application. The following objectives are expected to be achieved through this experiment:
1. To understand the structure and working principle of membrane bioreactors;
2. To master the design and operation parameters of membrane bioreactors;
3. To determine the effectiveness of membrane bioreactors in treating various wastewaters;
4. To explore methods to prevent membrane fouling and membrane cleaning methods.
3. M*n technical indicators and parameters:
1. Ambient temperature: 5℃～40℃
2. Processing flow: 5～10L/h,
3. Device dimensions: 1300mm×400mm×500mm
4. Working power supply: AC220V±10%, 50Hz, single-phase three-wire system, power 800W, safety protection: with grounding protection, leakage protection, overcurrent protection,
4. M*n configuration:
1. 1 raw water tank: white PP board material, thickness 10mm, 300×400×500mm, a dr*n valve is installed on the bottom plate to facilitate the dr*nage of water;
2. 1 clean water tank: white PP board material, thickness 10mm, 200×400×500mm, a dr*n valve is installed on the bottom plate to facilitate the dr*nage of water;
3. Equipped with 1 raw water tank stirring motor , 1 set of 304 st*nless steel stirring paddle; (power 25W, speed 120rpm), (including 1 speed regulator)
4. 1 set of anaerobic reactor cylinder, with jacket insulation, transparent plexiglass material, wall thickness 8mm, Ø300×700mm, accessories include: 1 set of 304 st*nless steel heating constant temperature water tank, 1 set of temperature control system, 1 set of anti-corrosion circulating water pump,
5. 1 set of membrane bioreactor, 1 set of curt*n ultrafiltration membrane assembly (Tianjin Membrane Tianmembrane brand),
6. 1 set of anti-corrosion lifting magnetic water pump, flow rate: 16~19 (L/min), head: 2.7~3.4 (m), power 20W;
7. 1 set of *r pump, power: 40 W, maximum *r volume: 8L/min,
8. 1 set of diaphragm suction pump, working power supply: 24V, power: 120 W,
9. 1 set of stirring motor, 1 set of 304 st*nless steel stirring paddle; (power 15W, speed 120rpm), (including 1 speed regulator)
10. Flow measurement and regulation: 1 rotor flowmeter, (6~60L/h)
11. Flow measurement and regulation: 1 gas flow meter (250-2500L/h)
12. Flow measurement and regulation: 1 water flow meter (1-10L/h)
13. 1 set of programmable automatic controller
14. Power supply control system: 1 double-sided matte dense spray plastic electric control box, leakage protector (Delixi brand), voltmeter, lockable button switch, wire pipe, etc.
15. Matching UPVC connecting pipes and valves (Zhongc* brand).
16. St*nless steel frame test bench (30mm×30mm st*nless steel square tube, equipped with casters for universal wheels with locking feet) and other components.
17. Virtual simulation software for electrical installation of building and intelligent building Based on unity3d design, users can choose different sizes of interactive interfaces according to computer configuration, and can choose six levels of image quality. The model in the software can be rotated 360°, enlarged, reduced, and translated. There are assistant prompts during the use of the software, the contents are as follows: A. Wet alarm system 1. System overview: Overview of wet alarm system 2. Equipment recognition: It is equipped with the best viewing angle, equipment det*ls (displaying the introduction or parameters of the equipment), exercises (built-in 6 multiple-choice questions, with prompts for correct and wrong choices), and schematic diagrams (you can enter the equipment from the schematic diagram). The equipment includes: sprinklers, water flow indicators, signal butterfly valves, exhaust valves, fire alarm controls, high-pressure gauges, high-level water tanks, Wia control cabinets, pressure-stabilizing tanks, flow switches, terminal water testing devices, dr*nage facilities, water pump connectors, hydraulic alarms, time delays, wet alarms, butterfly valves, check valves, fire pumps, safety pressure-stabilizing valves, and fire water tanks. 3. Principle display: Display the working principle of the wet alarm system, 3D animation demonstration, and semi-transparent 3D models, so that the internal water flow can be seen. Equipped with a practice module (built-in 4 multiple-choice questions, with prompts for correct and incorrect choices) 4. Design layout: There are multiple-choice questions and calculation questions, each with a score, and the correct answer and score will be displayed after submission B. Gas fire extinguishing system
1. System Overview: Overview of gas fire extinguishing system
2. Equipment recognition: It is equipped with the best viewing angle, equipment det*ls (displaying the introduction or parameters of the equipment), exercises (8 built-in multiple-choice questions, with prompts for correct and incorrect choices), and schematic diagrams (you can enter the equipment from the schematic diagram). The equipment includes: nozzles, HFC-227 storage bottles, bottle head valves, heptafluoropropane one-way valves, high-pressure hoses, gas one-way valves, safety valves, weighing alarms, electromagnetic starters, selection valves, smoke alarms, and fire alarm controllers.
3. Principle display: Display the working principle of the gas fire extinguishing system, 3D animation demonstration, and the 3D model is semi-transparent, so that the internal gas can be seen. Equipped with an exercise module (3 built-in multiple-choice questions, with prompts for correct and incorrect choices)
4. Design layout: There are 6 multiple-choice questions, each of which is scored. The correct answer and score will be displayed after submission.
C. Escape drills: Teaching is carried out in the form of fun games. Escape from the burning room within a limited time. If you make a wrong choice, you will directly enter the score interface.
Similar products:

ZR-269
IC anaerobic reactor device

M*n parameters and configuration:
water treatment capacity: 2-4L/h, cylinder diameter is Φ200mm×1500mm. Device dimensions: 1000×500×2300 mm, power supply 220V single-phase three-wire system, power 800W, configuration: 1 set of IC anaerobic reactor device, 1, water inlet, 2, gas collection hood of the first anaerobic reaction chamber, 3, biogas lifter, 4, gas-liquid separator, 5, biogas conduit, 6, return pipe, 7, gas collection hood of the second anaerobic reaction chamber, 8, gas collection pipe, 9, sedimentation area, outlet pipe, etc. . It is equipped with 1 set of st*nless steel heating constant temperature water bath, 1 digital temperature controller, 1 set of temperature control system, 1 metering pump, 1 circulating water pump, 1 biogas flowmeter, 1 set of programmable automatic control, 1 batch of sampling ports, 1 wastewater tank, 1 electric control box, leakage protection switch, push button switch, connecting pipes and ball valves, st*nless steel stand with moving wheels, etc.

ZR-270
Anaerobic bioreactor

M*n parameters and configuration:
water treatment volume: 2-5L/h, sewage retention time: 10-20h, cylinder diameter Φ300mm×800mm, device dimensions: 500×400×1700 mm, power supply 220V, power 300W, configuration: 1 anaerobic reactor, 1 set of separators on the upper part, 1 water distribution tank, 1 water pump, 1 electric control box, leakage protection switch, push button switch, connecting pipes and ball valves, st*nless steel stand with movable wheels, etc.

Previous：DY-262 Oxidation Ditch Training Platform

Next：DY-271 UASB anaerobic fermentation column training platform